FT8 – Hydraulic System – Servo control
FT8 – Hydraulic System – Servo control. This explains how the servo controls the position of the IGV and VSV. Continue Reading →
Technical information useful for learning & troubleshooting.
FT8 – Hydraulic System – Servo control. This explains how the servo controls the position of the IGV and VSV. Continue Reading →
Solar Turbines – Surge control – 289RC Exhaust Booster. This instrument is used to assist the surge valve to open quickly. This post explains how the instrument works. Continue Reading →
FT8 – Hydraulic System – Maintenance. This post will give a an overview of the Mechanical maintenance requirements of the hydraulic system. Continue Reading →
FT8 – Hydraulic System – Maintenance 2. This will focus on the instrument and control maintenance of the hydraulic system. Continue Reading →
Solar – Mars 90/100 – Pre start-up fuel valve safety check. This explains the sequence of events to pass. Continue Reading →
FT8 – Hydraulic System – Part 1 – Overview. This is the first in a series of blogs on the Hydraulic System. Continue Reading →
This explains how analog input signals are processed in Solar Turbines PLC logic. Continue Reading →
FT8 – Lube Pressure control valve PDCV601 – dissembled. Continue Reading →
FT8 – PDCV601 – Description of operation of lube pressure regulator PDCV601. Continue Reading →
Stripchart – Vern Van Leuven – Information about Stripchart and Vern’s services. Continue Reading →
Solar – Backup pump control – this control needs maintenance. Continue Reading →
Solar Titan 130 – oil flushing issues and things to watch out for. Continue Reading →
Solar Turbines – T60 – G353-1 backup overspeed calibration. Continue Reading →
FT8 – FCV1101 – this is the second part of this issue. Disassembly of the motor. Continue Reading →
This article shows how to dissemble a Woodward fuel control valve FCV1101. Continue Reading →
FT8 – Mobile – Good Idea – These are a couple of good ideas that customers came up with for the FT8 Mobile Unit. Continue Reading →
Solar – Ignition Issue – This is an old issue with TT3 control system. The turbine would not light off reliably. Continue Reading →
Good Idea – simple yet very effective walkway support to gain access to your turbine. Clever Chileans. Continue Reading →
FT8 – Turbine – IGV / VSV. This is a very useful troubleshooting tip that gives you the heads-up on pending IGV / VSV issues. Continue Reading →
Solar – T60 – This explains the operation of the L339 operated solenoid valve 1016391. Used in standard combustion T60 and Centaur units. Continue Reading →
Some good maintenance tips on the FT8 Air System. The stuff you don’t find in the manual. Continue Reading →
FT8 – Hydraulic System – IGV / VSV startup data. This is very useful data for reference when you have issues. Also a very good useful tool to check the if the current position of the IGV / VSV. Continue Reading →
ARTICLE REF – ART011 Alignment shim calculation T60 mobile unit The following information will serve you on all alignment jobs regardless of the manufacturer. It is very important to have a good understanding of what shims need to be put where when it comes to making an alignment adjustment. This … Continue Reading →
ARTICLE REF – ART010 Part 2 Alignment information sources. Alignment tools and setup. Three readings to satisfy spec. Torque values. Alignment information sources. Mechanical Installation Drawing 149223. Chapter 9.5 of the maintenance manual (IMI). Installation guideline No. TPIM 1000B. Alignment tools and setup. This is the type of tool you … Continue Reading →
ARTICLE REF – ART009 Part 1 Total Indicator Reading. Soft Foot. Changing target sides. Bore and RIM Readings. Magnetic center. Hub to hub distance. Tool sag. TIR – Total Indicator Reading Question: The dial test indicator (DTI) is zeroed at the 12-o-clock position. The shaft on the right is turned … Continue Reading →
ARTICLE REF – ART008 Solar Turbines – Project documentation. This is a short description of the documentation supplied by Solar Turbines for each project. This information is normally provided in hard copy and software versions. In the software version there is a main listing with hyperlinks to each of the … Continue Reading →
ARTICLE REF – ART007 GG / PT remove & install This is a quality document which would be very useful for training new technicians or to be used as a safety job review etc. The author is unknown but it took a lot of effort and is a quality 25 page … Continue Reading →
ARTICLE REF – ART006 Maintenance Board. This was a photo taken of how one customer used a white board with stuck-on labels and a marker to keep track of the hours in service and to control what filters on standby were used or new etc. At a glance you had … Continue Reading →
ARTICLE REF – ART005 During commissioning of the fuel gas system the gas valves were stroked from the ICE calibration screen and found that each one stopped at 90% with a “valve failure” annunciated when the command signal reached 97%. It was expected that the valve would move the complete … Continue Reading →
ARTICLE REF – ART004 Some years ago there was an issue on a site where an operator got an alarm “Gas Fuel Valve”. The alarm would not reset by software resetting from the ICE display and it was decided to change the gas fuel valve. The control system was powered … Continue Reading →
FT8 – BRUSH generator hold down to skid. Information assembled from different documents. Continue Reading →
FT8 – Issue with the new design thermocouple. Continue Reading →
FT8 – Lucas coupling removal tips and warnings. Continue Reading →